Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
I'm working on a PC application (using nrf51-ble-driver_win_0.4.1 API) to connect a BLE device and discover BLE services.
Today, I'm tying to connect the Nordic dev kit...
When discovering services using nrf51-ble-driver_win_0.4.1 driver, some ID are received with type BLE_UUID_TYPE_UNKNOWN. So I assume they are 128bits. I then retrieve the...
I downloaded the BLE beacon app S110 v7.1.0 to a nRF51-DK board. The current measurement pins were attached to a 10 Ohm resistor.
I observed the AC-coupled voltage at one...
Hi. We've got a chip with a code QFACA10. I am trying to find out if there is the internal pull-down of SWD line or not. It seemed that adding an external pull-down had positive...
Hi all,
I want to know the effect on power consumption of pins input buffer on and off, does there are big differences between them?
Another question is, since there...
Hey everyone,
when i was trying to compile i got this error which says
._build\ble_app_bci.axf: Error: L6200E: Symbol SWI0_IRQHandler multiply defined (by nrf_notification_manager...
i have few question based on nordic i am using N51822.
1: does device goto sleep, while testing i see sometimes device gets automatically disconnected.
how can i solve...
Hi,
what would be a good option to create a BLE device like FLIC (flic.io).
i want to transmit only a few informations to the smartphone like 1,2,3,4 and the device shall...
Hi,
every time i try to call ble_bas_battery_level_update(&m_bas, 1); my application freeze and i can't get any response
Here is what i did:
1- copying ble_app_template_s110...
Hello folks
I have a custom PCB board with the attached layout diagram. I also have our firmware that was flashed on to the Nordic beacon kit and tested. I would like to...
Hello,
at the moment I try to add some more services to my BLE device. This goes wrong with err_code = 12 (NRF_ERROR_DATA_SIZE). With some search in the devZone I found...
