Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I was wondering if the Master Emulator API requires the Segger IC on the nRF51 Dongle (PCA10031) to work? Or is this just used for programming the nrf-device via USB?
The...
Hi.
I'm using latest version of nrf51-pwm-library to test if PWM works fine, but unfortunately, it's not. I have very simple program which should fade LED from 255 to 0...
Is there an application note or specification that defines the term flash memory endurance and flash memory retention?
What failure modes can be expected when these specs...
Hi.
I faced very weird problem.
below is my structure of custom array;
if I set MAX_MYARRAYCOUNT as 20, it's OK.
but if I set MAX_MYARRAYCOUNT as over 30, device crushed...
.HEX file of bootloader in below directory C:\nRF51_SDK_8.1.0_b6ed55f\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\armgcc_build
have not covert in zip file by nrf_utility...
