I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
In porting from SDK6 to SDK9, it looks as though
nrf_gpiote_task_config()
has been replaced with
nrf_gpiote_task_configure()
What, if anything, has replaced
nrf_gpiote_unconfig...
I'm using sd_ble_gap_address_set() to randomize mac address and it's working fine. But I'm confused about how to change it back to normal(initial value I see) once I wan't...
i cant find lbs example on \SDK8.0.0\examples\ble_peripheral\nrf51-ble-app-lbs-master\arm and compile.I planned to work with nrf51822 dk. The given example in github shows...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
Sorry but I've been stuck on this for a few days now and I have to give up and ask for help.
I'm attempting to set LED0 when BUTTON_0 is pressed and LED1 when BUTTON_1...
Hello all,
I am working on a device (nrf51 and s110) which is going to communicate with multiple centrals (smart phones).
The device uses a whitelist to connect to only...
Hi,
I run a custom board with an nrf51822.
If I program the device in the IAR IDE everything works fine but I cannot program the generated hexfile with nRFgo Studio or...
Is it 'NRF_RADIO->TASKS_DISABLE' or 'NRF_RADIO->TASKS_DISABLE = 1'?
Restarting advertisements seems not to be affected and I guess 'cancels out' NRF_RADIO->TASKS_DISABLE...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
