Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I want to generate PWM.
I set timer2 events_compare[0] to toggle pin 1:
sd_ppi_channel_assign(PWM_LED_HI_CHANNEL, &(NRF_TIMER2->EVENTS_COMPARE[0]) ,&(NRF_GPIOTE->TASKS_OU...
hi, I have posted a detailed problem using Eclipse on Vidar's tutorial.
Any help is appreciated.
See following link:
devzone.nordicsemi.com/.../
Thanks!
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I want to send a data of length 1024 bytes over the ble UART , but the maximum length of data is 20 bytes at a time. Is it possible to increase the data length per instance...
Hello!
I try to use "ble_default_bootloader_app.hex" with my app to allow OTA option for my device. (nrf51822 and SDK 7.2.0) With NRFToolbox I can connect to the device ...
Hi all,
How can it be that sd_ble_gatts_sys_attr_set function returns BLE_ERROR_GATTS_SYS_ATTR_MISSING?
With the first and second connect it returns success but the...
I saw that each CCCD or sys_attr should be persisted per connection, does it mean it should be saved on flash to be restored during next connection for same device ?
and...
If iOS of BLE master sends 4 packets of the same write characteristics with MD bit in the same connection event, how does SoftDevice of BLE slave work?
The ble_event_handler...
Is there a summary of potential pitfalls, i.e. issues which are asked repeatedly by users in these forums regarding HW/Schematic/PCB design for NRF BLE chipsets. Making mistakes...
I just published my port of a new FreeRTOS operating system version for the nRF51x22 and the nRF51 SDK 8.x.x to github.com/.../freertos_nrf51 , the README is copied below...
I am trying to implement some write to flash, and started by integrating the relevant functions from the example code I found in this thread .
I added a dummy write function...
Hello,
I'm building an aplication with multiple nRF51822 beacon modules. I'm using dual mode S130 softdevice. Sometimes, when beacon recieves a lot of messages, and forwards...
I'm trying to erase the page 32 of a nRF24LU1+ via SPI (using a Bus Pirate).
What I did so far:
Display the first 16 bytes of content of page 32: 0x03 0x40 0x00 0x10...
I have a switch connected on the nRF51DK Board. The switch is connected on PIN25 and PIN 28. I try to read the state of the switch.
My setup:
-nRF51DK
-SDK8.1
...
