Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
I want to use ANT and BLE concurrently.
I found that there are no multiprotocol examples in SDK12 for NRF51422 (PCA10028). It only have example for NRF52832 (ble_ant_app_hrm...
Hi all,
i use softdevice and app timer.
I know that the softdevice use a RTC0 and app timer RTC1.
I would use a rtc to have a timestamp. but i see that after 512 second...
My function need a time window to get value from sensor,but the prcess always interrupted by SD.I know that the priority of SD is higher than app functions. So how can get...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I'm starting to program a Nordic microcontroller, the nRF52. I was able to compile the various examples.
Now I would like to create my own project and use the...
The FDS requires data to be word-aligned and multiple of the word size. How do I ensure that my source/destination data structures are properly sized/aligned?
E.g. I want...
Hi, would like to know if anyone has some experience and advise how to get an external 51822 based board programmed and working via the nRF52DK. All the wiring works, I can...
pc cannot recognize nrf51 DK board.
what I have done.
erase all - not work (log.log attached)
power on with reset button. and copy J-Link OB-SAM3U128-V2-NordicSemi...
I have 5 nRF52832 development boards.....
I'm using Visual Studio 2015 and a Visual GDB plugin.
I have loaded and built the BLE Le example.
I start the debugging...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
