Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
Hi,
I'd like to design a custom software an win10
to help in design a custom hardware using nrf51822...
at this time I have an eval board (PCA10028) whit a custom firmware...
We are trying to dump DFU code using Keil into nrf51822 IC. We are getting error, we are using SDK12. we tried many solutions provided in devzone, we were not able to solve...
Hello everyone,
I am trying to congifure two gpio pin (pin 6and 7) in standard high drive mode 5MA because am trying to connect those pin to the speaker inorder to increase...
When I program the board the COMP and Timers work fine. Upon removing the debugger and resetting the board it also works fine. But if I subsequently power off the board and...
Hello.
I don't know difference of GPIO's input/output direction setting.
There is two register for gpio setting.
DIRSET : Dir set register
PIN_CNF[n] : Configuration...
Hi there,
Is it possible to call SOC library functions before calling sd_softdevice_enable()?
In particular, i want to set up my interrupts with sd_nvic_SetPriority...
We want to use 52832 to control 6 LEDs. it is easy to use 6 IO pins to make them on and off. but we need these LED to blink. so we want to use one PWM module to generate 1...
When using the nrf_drv for spi master there are no problems when compiling. If I switch the SPI configurations to operate as a spi slave the compiler spits out "non-trivial...
Hi All,
I have just started working on interfacing SD card with nrf52 using SDK 12.0. I have to write to SD card at a rate of 84 packets per second and each packet consists...
Hi
I am checking out NRF51822, NRF24LU and NRF24LE1.
Below are my design requirements:
Smaller the size, the better. 7x7mm is OK. prefer smaller.
Lower power...
Hi, Nordic
I have 3 nRF52 devicies, one as Gzll Host, two as Gzll Device.
they use Gzp to pair, when paired, two Gzll Device send payload via different pipe ( 2, 3)...
Hey everyone, I'm trying to use lmt70 with nrf51822. So, first of all, nrf51 has 10-bits ADC, the data sheet of lmt70 is recommended 12-bits of ADC.
I plugged the sensor...
I use nRF51822 (Multiprotocol Bluetooth low energy/2.4 GHz RF System on Chip).To transmit informations with smartphone.
I have to set up a self-certification application...
Dear Nordic.
Is NRF_POWER->GPREGRET register writing in NVMC?
FICR and UICR is saved in flash memory(NVMC) as written by [nRF51_RM_v3.0.pdf].
But, GPREGRET register...
Hi，
I have the following setup
Chip: nrf51822 chip
SoftDevice: S110
Firmware: dtm exmaple.
I use device test Bluetooth certification in korea(RF output from our...
