Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
As far as I understand the nrf51822 has only 1 hardware uart. I want to communicate with the esp8266 over uart using standard AT commands, but still retain debugging possibilities...
Hello,
i use the N5 starter Kit. So my problem is to find sending data on the computer. Where i can read this data information?
Thank you for your help.
Hello everyone,
When i get message from uart, i need to update my custom service's characteristic. I tried the code in the below, sd_ble_gatts_value_set function gives...
I have to connect more than one nrf-51822 dk and send theirs RSSI level, because i need to knows their posittion. Somebody could help me? Have some example similary to what...
I am using the nRf52 device with FreeRtos and SD132 version 11.0. The configUSE_TICKLESS_IDLE is set to '1' to allow the device to go to sleep. After the OS is started - there...
Hello Nordic users and employees,
I'm having a small dilemma. The device I'm building runs on the nRF51822 and needs to store a small number of bytes off to the side and...
Hello, it is to my understanding that profile & service do not have fixed forms. Services make up profiles and you can choose how many and what services make up a profile...
I I'm running the ble_app_blinky example under pca10028 on the nrf dongle pca10031 using sdk11. The dongle disconnects after 24 seconds. Can anyone point to me what is the...
A typical classic or BLE get paired with the phone/central, and normally the central can decide to forget/unpair it. In this case, the device (nordic chipset) which previously...
I had created application with enabling the UART service(as in Ble_uart_app example) and tried to update the Rx characteristics of UART service in connectable mode through...
I'm sending a write authorization reply using sd_ble_gatts_rw_authorize_reply() in response to a standard Write Request with one byte of data. When I set the gatt_status to...
I am currently dealing with a strange problem when trying to use DFU OTA. When I enter DFU mode on Master Control Panel and try and update I get the following two error messages...
Does anyone have a working copy of ble_cps.c\h
The BDS (version 1.0.2095.0) plugin (v.1.2.4) does not generate code that compiles under IAR EWB
IAR ANSI C/C++ Compiler...
Hi there, I'm definitely a newb when it comes to wireless communication and communication protocols so I'd like this question to be answered at a higher level than what I...
