Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I want to use another MCU(MT7688 run OpenWRT) as a upper monitor to DFU the nrf52832,But you know,the way of serial download for nrf52832 is use nrfutil with command that...
Hi There,
We are having an issue reading data from the ble_gatts_evt_rw_authorize_request_t.request.write.data buffer. We are writing the data to the characteristic using...
I need to receive both UART Service data and HRS service data on the app.
Currently I have seen on Nordik Connect app , both the services can be found and can connect and...
So we have the Arduino 101 board talking to a heart rate sensor MAX30100. When we run the nrf connect app on android it is able to connect to the sensor with no issues. When...
Sporadic program restart from main.
I suppose, it is hardfault exception. How can I catch it?
Check pls my memory settings.
ROM: start- 0x1c000 size 0x23000
RAM: start...
Im implementing an application which uses the s132 SD for BLE communication and the mesh implementation described at nRF51-ble-bcast-mesh. I need to have encrypted and authenticated...
Hi Forum,
I'm using SDK12 without ble. (peripherals/uart)
so, I can't pstorage or fstorage.
I want to write 4 bytes without erasing a page. And I want to update a value...
Hi. I'm using nRF52832, SDK13.0.0, S132.
When I make bootloader, I should make *.setting file for application.
Do i need *.setting file when I update just application...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
Hello,
I intended to implement an application without OS. Due to safety concerns I would like to have two call stacks : one for softdevice using MSP and the other for my...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
