This ticket concerns the expected behavior and recommended implementation for automatic reconnection between a bonded Central and Peripheral using Bluetooth LE Direct Advertising...
Hello,
I have a ble mesh with a nRF52840 Eval board and a certain number of nRF52840 dongle nodes.
I communicate via mesh Chat between the Eval board and the nodes.
...
A few years back I used a multilink project developed by one of the Nordic support personnel, to allow using the nRF52840 devkit board to talk to one of several Peripherals...
Hello,
I am having some trouble with the UART API (Async and interrupt). I am connecting the development board (nrf9151 DK) to a 3rd party device (keypad / prox reader)...
I'm working on an ESL project using the nRF5340-DK. I need to enable the PAwR feature, which requires Bluetooth 5.4. However, my current program is written using nRF Connect...
Hi Nordic Team,
am I currently evaluating the nrf5340 development kit for our new product revision and fail to get a power efficient shell besides rtt logigng.
Concrete...
Hi,
I want to set the reset bit to 1 in the reset register of Power Management module.
Chip used in nrf51822.
I have been trying to set the bit using the following statement...
how to send hex by nrftoolbox APP uart?
I use this app, when I start use it, I just only can send char, I can't send hex to the device. how to set it char to hex? please...
I am using the Nordic nRF51 SDK on a BLE Nano device. The example I am using uses a function to initialize the LED flashing (bsp_init()). This sets the timing for the ticks...
Hi all,
I want to use nRF51822 (s110) to measure the frequency (0 to 5kHz) of a signal connected to an analog input. Other posts ( like this ) show that a good way to implement...
Hi,
SDK:8.1.0
Chip:nrf51822
Power Mode:LDO
Battery:CR2450
Application:beacon
The equipment static power consumption is 3.3 ua, after a period of time is 1.9 ma,but...
I'm using Keil5 to compile example of SDK v12.2. And I'm trying to understand each of Source code to understand how each of it is consists of.
I opened an example "SDK...
My code hit weak handler when I try to modify the examples/peripheral/saadc to run with softdevice s140 on nrf82840 PDK. All I did was adding a BLE Stack initialization before...
On the nRF52832, what is the longest period of time that the softdevice will control the CPU while doing things with Bluetooth? This is effectively the interrupt latency time...
I am working on nRF51 and nRF52 series SoC.
I need to check whether my radio device is connected or not and also to test radio functionality(like radio range, sensitivity...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is it the only way to call a function on a read characteristic to make a read request and then inside on_ble_event call the function?
Is this the right way?
Hi
in the communication with an SPI peripheral device, a communication cycle might take up to 5 ms.
It is implemented as a blocking function, meaning that app_sched_execute...
Hi all! Several weeks I've tryed to implement code for my wireless temperature sensor based on nrf24le1 and ds18b20. In datasheet said that in memory retention mode the power...
Hi,
Is it possible to send a advertisements for a single (or a fixed number of) Advertising Events? I need to control the number of Advertising Events "sent" for a mesh...
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
