hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have run into two SAADC issues on the nRF52832 using SDK v12.1.0. Any recommendations on how to fix them?
Issue 1:
When the Keil compiler optimization is turned up...
Hi,
Has anything changed in subject of one peripheral connecting to multiple central devices? All I need is little number (~3) of concurrent links with mobile phones.
I have been working on a custom board that uses a taiyo yoden EYSHJNZXZ module.
A tact switch is connected between P0.21 and GND.
I want to use this switch simple input...
Hi All!
I'm working a few weeks now with the NRF52 DK and having loads of fun!
Today I tried to make a central/scanner that scans for packages from a broadcaster. To...
I am trying to understand surface finishing of PCBs. In order to do so, can somebody tell me that what kind of surface finishing Nordic uses in boards like nrf51 - DK where...
Hello!
I am designing PCA10000 based PCB. Unfortunately my manufacturer can't make PCB using prepegs and cores that used in PCA10000 (4.4 and 4.8). They can make using 4...
Hi Nordic
After download SDK12.1.0, I want to extend DFU service in my application.But i find it different with the pervious versions.
For example, i can know how to...
Hi,
I have just started a new project in uVision, using the ble-app-template from the peripheral examples. its running on a custom PCB, with no 32Khz XTAL, and i have changed...
The user manual only tells information of pins , active low such things of led on nRF52832 Dk. There is no detail information of components on nRF 52832 DK board. So, can...
After reading the FAQ on DFU I still do not understand how the bootloader and SD DFU are performed so that a failure during the upgrade does not brick the device (see answer...
Hi,
I have some queries about ESB RF Communications.
1.The address : is it possible change RF communication to one node(Tx) to multiple nodes(Rx). If Yes, Where can...
Hello,
I found that after using SPIM I have forever additional over consumption (additional 400-500uA).
It was solved here in forum
And there is errata 89
[edit]...
I use Gazell to acomplish one host --two device.When i just have one device,everything is OK。But when added to two,it cannot work.
I think,whether channel of two devices...
Hi, I am looking for the test report on the bluetooth emission of the NRF52832 that we use in our product. Could you send it to me by email? Thanks,
Emeline
