Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
in the NRF52832 documentation the TX chain delay is 0.6 µs while the RX chain delay is 9.4µs.
Does that mean if transmitting two packets in a row to the same receiver...
Hello everyone,
I have been using nrf52 IoT SDK for MQTT implementation. Everything works fine as long as I am publishing or receiving only one character i.e.
param...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
In Eddystone example in SDK 12.2.0, APP_MAX_ADV_SLOTS parameter is by default 5, but if I try to use less than 5, an error appears in es_flash.c because in the code, 5 slots...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
Hi there!
I found out that there is some problem in the example ble_app_hrs_rscs_relay in nRF5_SDK_11.0.0_89a8197. I want to restart advertising when adv timeout. I did as...
I'm trying to use app_timer_cnt_get() to implement an RTC Calendar system on a Gigawit module (nRF51822).
I have a test app_timer that has presacler=0 and period=3 seconds...
This is no a question, but i was not sure where to post it.
I was trying to use the nrfjprog command with the new version of SEGGER JLink, but the terminal output was ...
Hi! I'm trying to work with the beacon kit, but I have some confusion about which type of sdk I can use because with some example that I have found it doesn't work.
Besides...
When i use ble_app_hrs to connect with hrs demo(ble_app_hrs example), everything is ok.But when i connect to a heart rate monitor, it always disconnect.The print information...
I try to stop the advertising by using ble_advertising_start(BLE_ADV_MODE_IDLE) when the advertising is ongoing. It fails.
Please tell me how to stop advertising when the...
I have a problem where a central device (iPad) has to connect to a peripheral (running nrf51822, s110) as quickly as possible, receive data and disconnect again.
Right...
