Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The documentation for the nRF52840's SAADC mention optional resistor ladders. What are they for? I see that the documentation specifies that the ladder's resistance is 160kΩ...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello friends,
I'm having MDBT40 EVB which is cheap one as compare to other but with lack of build and debug support. But i dont know how do i flash my hello world blinky...
developer.nordicsemi.com/.../a00935.html
The doc seems to provide only write functions.
And, the flashwrite example doesn't show how to read from flash even after device...
Hello,
I am currently looking through my error handling and noticed that there are some errors that I do not really understand fully, so I've summarized them here:
0xDEADBEEF...
Hi,
I am trying to make a communication between a nRF51(uESB) and a nRF24(ESB). The uESB uses tx_payload and rx_payload as buffer to send data. Bytes 0 to 4 are used for...
Dear Nordic team,
I've seen very much reproducible crashes of your Android nRF Master Control Panel app when trying to see details (button "MORE") of particular Peripheral...
Hi Nordic,
Is there a way to follow blog posts the same way as standard questions? I haven't found anything and it's really painful when you want to follow discussion or...
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware:
• nRF51822 Evaluation Kit (PCA10001) and a mini USB cable...
hi, i am a beginer in BEL application.
after some tries, i can compile and download 'ble_app_uart'.
but the module does not work at all also it dosen't advertising....
...
i make a new "Makefile! project" using example in SDK first i use the "blinky" ,
it looking likes can be work, then i try to use " blr_app_hrs_c " ,
i do the same step to...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
I'm trying to develop a minimalist android app to send and receive data with my nrf51822 dev-board.
Can anyone please tell me where I can find a great project example?...
Hello,
In our project i am using nrf51822 with stack Softdevice S110 . We want to connect it with Samsung Gear S2.Is it possible with stack s110 or i have to use stack...