Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
hello,
i am using s120 softdevice along with nrf6310 mother board, the problem is i am dumping the code into the device, but i am having doubt how to verify that it is...
Hi, I am creating a PCB design and am not sure if I should connect the pad under the nRF24L01+ to the ground plane with a couple of vias.
The data sheet says it should...
Is there a plan to support the BLE central role in the software stack?
As it is now, I absolutely cannot use the nRF51822 since the S110 stack does not support operating...
The attached test program and logic analyzer displays shows that the function twi_master_transfer() returns to the calling program before the transfer is complete, if TWI_hw_master...
The error I get is app_error_handler 0xDEADBEEF, 360 (line number), src\ll_lm.s0.c
This is with SD 5.2.1
With SD 6.0.0.1-alpha, sometimes I get
app_error_handler...
Does anybody know of any plans to combine the Peripheral and Central roles into a single SoftDevice?
The killer application that this provides is the ability to create...
Hi All,
I use nrf51822 transfer data to nrf uart app for android,when I use following parameter ,the device and nrf uart app work well.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS...
I'm interested in advertising with data type 0x18 random target address. I found a post for advertising with 0xFF manufacturer specific data. What changes are necessary for...
Hi,
I am using bluez 5.12 and am having difficulty connecting to an nRF51822 EK running the Health Thermometer application and Soft Device S110v6.
I am able to see the...
Hello,
I cannot build a known-buildable project and get error A1023E.
No Programmer's Reference exists and there is no documentation referencing this error.
I think...
I want to quickly transfer data between nRF51822 and celluar phone. The data rate is 100 packets/sec. Packet size is 14 bytes. We know mouse can reach almost 200Hz report...
can i use j-link debug probes to program and debug evaluation kit?
recently i bought J-Link debugger from the segger, i tried to find the pinout of the SWD of the eval...
I see that the source code of app_gpiote.c uses NVIC_... functions to handle the interrupts:
app_gpiote_init.c, line 160...:
NVIC_ClearPendingIRQ(GPIOTE_IRQn);
NVIC_SetPriority...
My question is regarding the adertising with the softdevice on the heart rate sensor example.
My starting point is the following:
I connect PCA10001 / PCA10000 from...
Hi,
we are interested in the combination of the nRF51822 with a sensor board which was announced in October but since then there were no updates and I can not find any other...
