Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
recently I experienced a strange behavior on the nRF51 chip, that is at a certain point some gpio lines remained held high, even if the firmware set them to low (both...
I clone the repository on GitHub, which is the accompanying code for the Application Note nAN-36 "Creating Bluetooth Low Energy Applications Using nRF51822", in the nrf51822...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Hello all.
I am now making a central device to control a peripheral device.
The Firmware of central device is supposed to be updated by Smart Phone, like iOS or Android...
I'm currently making a device which use nRF52832 and that will integrate Capacitive touch feature. However, I'm actually a bit lost with this post: devzone.nordicsemi.com...
Hi, I use PCA10040 v1.1, Keil MDK 5.21a, SDK 12.1 with S132 v3.
I was using SDK 12 previously. The SDK 12 projects worked well.
Now I migrating to the new SDK. So...
Hi all, I'm working on SDK11.0.0 with softdevice S130 v2.0.0 and I need to update bootloader+application at the same time in single zip for these I created zip file by using...
I have a use for the pstorage module and while going over the implementations in the Nordic examples and libraries, I found a use-case of pstorage_register() in bootloader_init...
Hello,
I would like to use the PCA10028 close to the conditions of a future custom board at 1.8 V (including I/Os) but I would like to keep the ability to do source level...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
