Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
After connection, if i want to change SUPERVISION_TIMEOUT, is it possible?
If it is, how can i do that?
I need...
Hi.
I am trying to get the RTC started, and I've followed the rtc example in the NRF51_SDK.
But things go wrong when I call:
ret_code_t err_code = nrf_drv_clock_init...
Hello , RX: nrf24LU Tx: nrf51822 use ESB Lib. But the nrf24 Can't receive data continuous.
if I Want receive 2th data , I must power up the nrf24.
This is my Code :
RFCTL...
hello,
I wanted an info which tool is better for debugging when using
native SDK.
do i have to use pyocd or openocd for native sdk hardware debugging
and if you can...
Based SDK 9.0 "ibeacon" example, nRF51822(QFAAG0) work's well when download the ibeacon.hex.
The target set as follow:
Based SDK 9.0 "ibeacon" example,nRF51822(QFABC0...
Anyone seen the new nRF52 online power profiler ?
It's an online tool that estimates the current consumed by your BLE application.
This allows you to better understand...
Hi,
Before starting advertising using advertising_start() function, if pstorage function is used to write data, then it gets stuck at that point as no pstorage handler...
Hello, I have an issue with ble_app_hrs_rscs_relay that doesn't seem to exist with the other sample projects.
The project compiles without any issues, but when I run it...
Apart from pressing Button 4 or adding a DFU service to current running application. Is there any way to enter DFU mode from application?
Is it possible with nrfutil to...
Is there any tutorial or good example for I2C communication using TWI? I already saw the examples for TWI, but I don't find them very intuitive to change for I2C.
I'm trying...
After updating an application on nRF51822 chip with a new application which has new Characteristic UUID via BLE, iOS app cannot detect the new Characteristic UUID.
I know...
Hi to everyone,
I'm trying to use the CMD Mode of my Sniffer but I have different problems. First of all, when I switch to the CMD Mode the red LED didn't blink (it doesn...
`Hi Guys,
I have some sensor data of 20 bytes at each measurement at different period stored in EEPROM. Now i have to transmit all data over BLE continously.
example ...
