Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am trying to change an example code on ble_app_uart_c (Central) SDK10.0.0 s130.
I have changed already peripheral example and I can see notification data if I...
Hi,
while flashing the device i get "Contents mismatch at: 0001C1C0H".
I am not sure if my IROM1 and IRAM1 settings are setup correct in the Target Settings of my Keil project...
Hi,
i have two microcontrollers: STM32F401 and nRF51822. They communicate by uart with flow control. I use 110 Soft Device from SDK 10. The maximum baud rate when communication...
Hi All,
I am trying to update the HEX file of LED_mesh example using DFU bootloader over-the-air. The LED_mesh application HEX file gets uploaded successfully by bootloader...
Hi Nordics,
I copy pwm sample code into my proximity project, to drive a buzzer .
I init pwm before softdevice. but, once "SOFTDEVICE_HANDLER_INIT" is excuted, the buzzer...
Hi,
i have a problem with nRF51 an nRF24LU1+. I use S110 and micro-esb library. I can switch beatween poroperty RF and bluetooh ( never run both in the same time ). When...
I wanted to use the SysTick timer for timing in my application, but even when writing a handler and trying to set it up, it doesn't seem like the interrupt is ever triggered...
hi I am i using Keil to debug the progam, it seems like that the printf() function can't work in keil, so i use jlink RTT to perform the printf function to collect data ....
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
Hi,
The function sd_ble_enable(ble_enable_params_t * p_ble_enable_params, uint32_t * p_app_ram_base) requires now the application RAM base address! Is it 0x20002800?
Hi ~
I use nrf51-micro-esb on GitHub
In Tx-Device: auto sent (data+1) to Rx-Device
But Rx-Device receiver data still the same not Increment....
why in Rx-Device...
Hi everybody
Since quite a long time since my last visit here. Now I come back because a new project using the NRF51822. Because now I'm using the NRF51822-CEAA, I can...
Hello,
I am developing an application where in i want to create a network with One central[not a mobile,pc,tablet etc] and multiple peripherals connected to the central excahnging...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
