Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
We tried to run the blinky example in the contiki source tree, and we had a strange behaviour. The example code is here , and the hardware is here .
The issue is...
Hi,
I'm using a RF module with nRF24L01+. Sometimes the RF stop working, the module keep replying status of no rx data (all pipes).
The device is embedded into a device...
Hello
I'm testing latest examples on 10040 (SDK12 S132). I want to get autoConnect working on Blinky example with nRF Connect app but I'm unable. Has anyone tried this...
HI all Nordic Developers,
Recently, I am using nRF51 DK as a beacon scanner connected to my laptop (Baudrate: 115200), it works fine to detect the beacon broadcast from...
HI,
I am using development board of BLE nRF52832 battery which you provide CR2032 is support for good battery backups
please give the reasons behind in it?
Hi all,
Is the "to-be-sniffed" advertisement packet allowed to have incorrect CRC, or perhaps a missing CRC? I.e. Is it possible for the sniffer to just display the raw...
Hello,
A problem occurs when i run the DFU over UART on my board.My bootloader project references to nRF51_SDK_9.0.0_2e23562\examples\dfu\bootloader\pca10028\dual_bank_serial_s110...
ANT experts,
I have been looking at the nrf52 implementation of the ANT timestamp (and timesync) features. One thing that is rather puzzling is the fact that the documentation...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
