after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am debugging a small program for the nRF52, which uses the App Timer and communicates over UART. I am trying to keep up with bug fixes, and so I'm using SDK 11.0.
The...
We have an application that requires a fairly quick disconnect (under 250msec) when the RSSI exceeds a threshold, for example -80db. Unfortunately, around 1 out of every 4...
I am trying to program a nrf51822 module using the nrf51-dk.I have made connections as per the nrf51-dk user guide, but sme is not working...
I am using the Vdd of the...
Hello all,
In a network of sensors with power constraints in a room which protocol is the best?
Newer devices seem to use BLE but I don't want to discard good old nrf24l01...
HI, I try to turn on the OLED.
I can not confirm that the lights turned on
I want to change background color.
What should I do?
Currently being output as shown...
I have installed Keil v5.18a
and have installed MDK for nRF51-DK.
Examining the basic LED blink examples showed that in some projects, the 'bsp.h' which would be the header...
I just setup Eclipse and trying to compile.. I was getting warnings.. I think I have installed all the relevant packages.. But still getting following warnings. Am I missing...
Hello! Developer,
Does anyone know how to transfer and store the value as big endian on memory address on nRF51 and send it over BLE to display value on MCP as big endian...
Hello!
I'm trying to get the 16 bit ADC value as 2 of 8 bit array from nRF51 development kit over bluetooth to MCP, but when it displays on the MCP the value is "swap"...
Is it a good idea to use nRF51 standalone as an Application Processor and also as BLE connectivity chip?
OR
Is it a good practice to use a separate Application Processor...
I have a question on - to me - seemingly weird behavior about copying data out of the event from the soft device.
Situation: I have a 32 bit integer characteristic which...
Hey all!
Newbie here. I developed and tested some code on an NRF51DK easily enough using mbed, and now I'm trying to put it onto a PTR5518 module from Xuntong (which I...
Could you rub my nose in Bluetooth SIG Core or just explain what does chip do when switching to very noisy channel? For example Wi-Fi working very close to our device.
Hello:
I have read the documentation but I cannot determine if INPTR and OUTPTR can be set to the same memory address? I will try it to see what happens but it would be...
