Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
I have some very basic code that does not appear to be executing correctly.
There are two versions of code that I would think should have the same result. They do not,...
I am having trouble with setting priority of ADC_IRQn.
void ADC_init(void)
{
nrf_adc_config_t nrf_adc_config;
nrf_adc_config.reference = NRF_ADC_CONFIG_REF_VBG;
nrf_adc_config...
I'm using the nRF52-DK (SDK11.0.0+s132) and added in some example code from the RTC example (the RTC2 tick interrupt with prescaler=0 to toggle a GPIO) to the ble_hrs example...
Hi there!
I don't know much about FCC, UL, CE certification and want to learn. I am using the blend micro module which uses nrf8001 chip in my project. How do I get my...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
Hi,
I am using NRF51822 and SDK11 with S130. I have enabled WDT with 2000 as reload value as I'm using 1 second timer. But I want to immediately reset when a certain condition...
Sir,
We are using your radio component in our system since many years. We are in the process to get conformity with Japanese rules.
The lab in charge of testing is asking...
Hello,
I'm trying the ota tester with pca10040 board however the ota tester won't run.
System hangs around softdevice_enable() and goes to app_error_fault_handler. ...
In Android 5.x (API 21) and up, we are experiencing a problem with our BluetoothLeScanner, on some Samsung models like S4 Mini and S5 Mini.
More precisely, an error is being...
