Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Sorry for probably stupid question..
All the time in SDK we set need bits through the mask, for example
NRF_GPIOTE->CONFIG[idx] |= (pin << GPIOTE_CONFIG_PSEL_Pos) &...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
Hello,
i am new to BLE,
I am using the iot S1xx Softdevice on the nrf51 Dk in order to test ipv6 connection, and now i want to add advertising with the Eddystone protocol...
Sorry I am new to this. Therefore this question may seem to be odd:
I want to build a temp monitor using an nRF8001 (BLE Board Adafruit) and send this data to my mobile...
This is the code I am using to wakeup my system from OFF. It is not working. Kindly Help.
#define Pin_0 0
static void gpio_init(void)
{
ret_code_t err_code;
...
I am creating a system (nRF52 SDK11.0.0 s132) that will get a data ready interrupt on a GPIO (configured via GPIOTE with a handler) from a sensor every 4ms. The sensor has...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
We've currently only been developing our application in C. We now have a couple of C++ libraries we'd like to use and are having trouble compiling the mixture of C and C+...
On a custom board using the nRF51822, with SDK 11.0.0, SD s130 and gcc, I'm seeing the following stack trace when doing some TWI operations to program an accelerometer:
...
I have to send a data to more units, i have found problems with multiple ACK return signals (I think this is the problem).
So i'm trying to send data with no ACK.
For this...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi.
I've played around with the android application (based around google gatt example, but used in gatt server -mode).
How is the example expected to be handled? In...
Hello everyone,
I am currently trying to make simple exchanges with an NFC chip using SPI.
Configuration is: nRF52 on dev board 10040 with example from SDK12 located...
Hi,
I have such code:
static buf[9] = {initializers};
for(i =0;i <9;i++){
while(app_uart_put(buf[i]));
}
I always get "0" before the actual buf content and the...