It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Now i know the Cortex M0 does not have a floating point unit. Does this mean that we cannot do floating point calculations in our application? or is there a library that will...
Development environment : keil mdk 4.7, nRF51822, SoftDevice 6.0-alpha, nRF51 SDK 4.3
Hello
I develop the application with RF and BLE by receiving UART msg. So, my program...
Section 8.1.2 of the nRF51822 Product Specification states that the "Standby current for 16 MHz crystal oscillator" is 35 uA. The footnote says that the current is drawn ...
Hi,
I met this prompt(see attachements) when I install nRF51 SDK. Who can tell me what's mistake it likes? I have installed microsoft .NET framework 3.5 before in my winXP...
Hi,
i programmed the softdevice with nrfgoStudio but i get an error and i can't load the softdevice on the chip again.
The Error means that the cpu is not halted and that...
Hi guys,
I hope you can answer my question:
I made myself a custom pcb for testing purpose. I can program the nRF51822 just fine. Thats the actual state right now.
...
I have a nRF51822 dev kit, and my dongle is running the master emulator firmware, and master control panel is running on my computer, the dongle is connected and started discovery...
Dear Nordic, could you please comment on your plans to release an over the air bootloader for nRF51822? What is the approximate time frame that we can expect that? Is there...
hi,
I am using nRF51822 chip, I want to added a presentation format to declare a custom characteristic as an array of float (float [3]). According to developer.bluetooth...
I need to program the hex application image into the PCA10001 board. However, if I program the hex file generated by the Keil compiler using nRFStudio, the application does...
Hi,
I'm creating a new service based on the heart rate monitor example, but I'm having some trouble with it.
I implemented my own service, keeping it as similar to the...
when the peripheral and the central are connected,the peripheral will transmit data to the central ,how can i know if the data was transmitted successfully to the central...
Hi,
i want to use the adc, i use the code from here devzone.nordicsemi.com/.../is-there-an-example-code-for-using-pwm-on-the-nrf51822-with-a-softdevice and it works fine...