Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi, GSMA Database suggests that nRF9160 has 2x IMEI, however I am only able to get one. Pakistan Telecommunication Authority is not allowing me to use the device till I provide...
C:/ncs/v2.9.1/zephyr/include/zephyr/toolchain/gcc.h:87:36: error: static assertion failed: "/soc/peripheral@50000000/uart@c7000 defined without sleep state" ,when i use the...
Hi,
I'm developing an application running on a nRF9151 that connects to AWS. I'm using the aws_iot library and my code is based on the aws_iot sample application. While...
Hi, I have a nRF5340 using hci_ipc that has the following features:
Central Role + Scanning (Multi-connection to nRF52840 peripherals)
Peripheral Role
QoS Channel...
Hello,
My name is Calvin and I am tasked with testing the NRF52840. I want to create my own development board for prototyping a project, but I do not want to keep plugging...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
Description:
I am working on an application using the nRF9160 and encountered an issue where the #MQTTEVT event is not triggered after connecting to an MQTT broker using...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
Hello,
I'm developing on a custom nRF5340 board without an external clock source - nRF Connect v.2.9.0. For my application, I'm using the internal system clock with this...
Hello,
I have made a PCB has 4 buttons and touchpad, now I want to drive all of them.
1. one button for left button of mouse. 2. one button for right button of mouse....
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hi,
I am attempting to get Direct Test Mode working on my nRF54L15 while also having access to the normal BT stack.
Normally, if I run dtm_tr_init(), I can begin the test...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
