Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
To whom it may concern,
I use a BLE app via nRF52832_WLCSP, 'ble_app_hids_keyboard' of SDK11(pca10040),SD s132_nrf52_2.0.0, with the HID profile. once I started advertising...
I'm currently using CrossStudio as IDE. I've no problem in compiling and downloading the application in the nRF52832 microcontroller. However the application wouldn't start...
What is the maximum number of connection a central device can connect and control in open mesh? Is 1 to 50 possible? What is the latency?
I am comparing to RFdigital Simblee...
I am trying to encrypt a write on a custom characteristic by setting:
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&attr_md.write_perm);
Then in the write event I read the...
I've tried getting a notification of subscription from a bluetooth event handler like so:
ble_evt_dispatch() is being called from main:
static void ble_evt_dispatch...
Hello,
I am using SDK v12.1.0 and I want to get the debug logs over UART
I followed the Logging Sink Configuration to enable UART logging and compiled the Health Thermometer...
Hi!
I was developing my custom service, and had a question around what kind of functionality is allowed or not allowed within a callback from the soft device or other peripheral...
Hi every one.
I am developing on S130 SDK 11 and I try to use whitelist connection for optimisation.
I have currently a working project which scan for 1 sec for any BLE...
My application is based on the ble_app_uart demo. I want to get the BLE approval from the lab. The lab want me to tell them the Bluetooth profile of my application. How can...
Hello,
I am trying to interface the STPC16CPC26 with the NRF52832. As per the datasheet of the display driver, we have to toggle two IO pins from the NRF which shall be connected...
I want to write protocol stack and my program to 518222 and now need the manually download device or the automatic download device. can you offer me the communication ways...
Hello
i am using Nrf52dk. i have Visualgdb.
i would like to use the Nrf5 IoT sdk in visualGdb.
i have some question. is that Nrf5 IoT sdk will support the SysGcc toolchain...
good time dear Engineers!
faced with a problem of S132 nRF52. ADV data of packet lost.
I compared the RAW data according to screens below:
If I use nRF Connect ...
Hi, Nordic
I see this question: devzone.nordicsemi.com/.../ , I follow it, then I can see log in J-link RTT viewer.
But when it work, I find after some time, the old log...
