Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
We want to design a setup for simultanious translation of up to 3 translators and up to 30 people receiving a translation.
Is it posible to setup a single transmitter, sending...
Hi everyone,
I am trying to monitor and measure the signal strenth variation by varying the positon of the developement kit NRF51 and i tried with the proximity example...
Hi,
I'm using v1.21 nRFgo. As programming 51series ,
(1)I want to know if the program check the hex file before the log dialog shows "programmed successful"?
(2)And...
I run nRF51 with S110 and advertising at least standard battery service. I can see my device in LightBlue scan window but in iOS Settings->Bluetooth it is not picked up. Which...
i am aiming to design a simple data transfer network. i am using 2 DKs. the first one is the central which runs a modified version of MULtilink Central Example and the seond...
I have continued to build upon the Nordic sdk10:gzll_ack_payload example using gcc-4.9-2015q1 on Linux. The differences are:
added UART for debugging (running at 460800...
Hello Nordevzone, so far, to the best of my knowledge, you can send data using API call sd_ble_gatts_hvx() with "notification packet" (quotemarks due to my limited knowledge...
AS i am trying to utilize GCC for more than 32 KB code size,
i use Eclipse which provides more friendly interface.
However, i am still experiencing some setting issues....
Hi,
Details:
I am using nrf sdk 10.0.0 and s130 Softdevice.I am using nrfgo studio for flashing SD,Application Hex files.I am using this nrfgo studio for past three months...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
app: nrf tool uart on iphone 5s
sdk: v8.1.0
softdevice: s110
example: ble_app_uart.
i have modify it based on the answer :
link text
my advertsing init as...
The device I completed has similar RSSI values at approximately zero distance as my development kit; starting with default Tx of 0dBm from the nRF51822 I achieve approximately...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
