I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I encountered an issue when trying to integrate DFU to my application. Every time I upload my application through DFU, the bootloader gets overwritten, i.e. only softdevice...
Hello,
I have to do a pre serie of a new product based on a NRF52832-QFAA.
I'm in Europe and I contacted local distributors (Mouser, ...) and there is no way to get...
Hi, when I run the ble_app_proximity on my 51822 board, I can connect the 51822 board with NRF Master Control APP, after a little while , 51822 disconnect with app, and trace...
Hi.
Is this issue resolved?
github.com/.../902
I tried lately using mbed-rtos with nrf51822, but no luck.
I would like to use threads, is there a way to circumvent...
Hello everyone,
i'm kinda new to microcontroller programming and feel like i bit of more than i can chew. I bought a variant of the nrf51822 chip ( github.com/.../Board...
Hi. Currently, i am testing the BLE power consumption on nrf52.I set connection interval 20ms(min=10,max=30) ,slave latency 0 and connection data size 20 bytes.in addition...
It seems like the IAR startup file in SDK 11 for nrf52 is older than the one that was included in the previous SDK 11 alpha
IAR Embedded workbench 7.50.3
I have a queston for softdevice S130 example about Environmental Sensing service.
I readed spec. but I can't find out any ESS profile example in SDK.
Is SoftDevice S130...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
