RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
Hi ,
I am using nrf5 SDK v12.2.0 ,
I have an nrf51822 board .. can I just compile the examples in SDK for pca10031 and use it for nrf51822 . Please let me know what I...
Is it possible to have two nRF52 devices connected in such a way to send UART data in a bi-directional way.
Would device 1 be a BLE central and the other BLE peripheral...
I followed the link: infocenter.nordicsemi.com/index.jsp to build and load the app into two boards.
Step 1 ~ 8 are working as expected. But
Step 9 "Observe that LED...
Dear Nordic,
What I want to do:
Battery powered sensor network
One gateway (BLE --> WLAN) with a serial-to-wifi chip connected to nRF52
MQTT (IBM Bluemix -...
Hi there,
I'm in the middle of migrating an application from SDK 10 to SDK 11. In the SDK 10 version, I had RTT logging working just fine. I'm developing on a Mac so I...
Hi guys
I am using customized board(Raytac MDBT40) based on nrf51822(flash memory 256k, RAM 32k).
I am trying BLE UART example code of SDK 11.
which path : \nRF5_SDK_11...
I am using S120 SoftDevice on PCA10001 board with sdk7. I want to know on which
channel i am receiving advertisement packets.
Is there any API on Central/Observer to which...
Hi there,
I was able to issue "make VERBOSE=1 mergehex" from my cmd line and it worked. When I do the same via build target from Eclipse, it is giving me "no such file or...
Hi,
In the product I'm working on I need to store some configuration data in persistent memory. I came accross serveral ways to do that. I think the best way to go is to...
