Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
We are treadmill developers and we want to include bluetooth capability to our products.
We found, on the bluetooth website the RSC characteristic ( Running Speed and...
When switching to nRF52_SDK_11, the compiler does not find core_cm4.h which is found in components/toolchain/CMSIS/Include.
I get this when compiling
nRF5_SDK_11.0.0_89a8197...
I am trying to program a custom board connected via the DK. The custom board is 16KB version (nRF51822 QFAA). RTT consumes lot of memory and hence my code does not compile...
I am using nRF51422xAC SOC.
It is advertising perfectly and able to catch that with sniffer module. But unable to find the same device on any mobile phone. I've tried with...
Can i use the nRF Toolbox app as a BLE peripheral and the nRF51-dk[PCA10028] as a central device.
Also,if not,then please suggest any other App that can be used for the same...
Hello,
I've downloaded nRF5_SDK_v11.x.x and install it, my keil version is v5.14. I flashed s130 v2.0.0 into nrf51DK, then build "ble_app_beacon" basing on SDK v11.0.0 and...
I use the S110-6.0.0 to find the iphone ANCS service,return attr missing. The 16bits UUID is xF431.I have added the long UUID ble_uuid128_t ans_base_uuid = {0xD0, 0x00, 0x2D...
Hi~
I used keil software environment for development.
Apply Ble UART example code from nordic keil example.
Example code down load to nRF51 Development Kit and run, program...
Hi, i need to calculate the frequency of two PWM.
When it comes to frequency calculation, the counter function is the best solution, i think.
i'm using SDK 6.0.0 for...
I want to develop an app that wakes app from sleep mode after pressing 2 buttons, then if these buttons are still pressed for 5 secondes i want to do an action ..
Any idea...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Is there a call to read the stack ID.
For example S120 v2.1 has an ID of 0x006B . nRFgo studio is able to read and report this value.
Is there a way to read for me to...
I'm using SDK 11.0 and example\ble_central\ble_app_hrs_c
I have cut SB1 SB2 to disconnect the 32Khz crystal from the pca10028 and configured the example program to use...
Hi, When I write data synchronously to memory (nRF51822), I do :
APP_ERROR_CHECK(pstorage_block_identifier_get(flash_handler, 2, &block_handler));
APP_ERROR_CHECK(pstorage_clear...
