Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
i am new at this so please bare with me.
i was using a nfr51822 with s110 version 7 and i now i want to migrate it to s110 version 8.
i have made a few changes according...
After checking bootloader example from the SDK version 10, I am not able to find appropriate ROM / RAM addresses configurations for 16kb RAM chip. The Bootloader examples...
Trying to run S130 V2.0.0 with ble_app_proximity on a BLE400 motherboard.
Im getting a hang at the call to SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL...
Hi,
We just received our custom board based nRF52832, below nRF52832 schematic
I succeed to flash the board. but i have frequency troubles.
I made a simple exemple...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have opened the nordicID sample project "InventorySample" for Windows CE in VS2008 it successfully builds the project but when i deploy it on mobile simulator Pocket PC...
Hi,
I'm using S132 v2.0.0 and nrf52832. I've got a problem when I'm trying to call any softdevice function from radio notification event handler.
#define RADIO_NOTIFICATION_IRQ_PRIORITY...
I am using nRF52832 DK and we designed a custom board using nRF52832. I am using a windows 10 lap. It used to program successfully from windows 10 lap and boards will advertise...
Hello,
I use nrf51 based device as peripheral with SD110.
I use connectable advertising ( BLE_GAP_ADV_TYPE_ADV_IND, BLE_GAP_ADV_FP_ANY ) and turned on BLE_GAP_EVT_SCAN_REQ_REPORT...
Hello,
what address in flash is it safe to store my application settings (some calibraton data) which should be preserved during application updates. I use S110 v8, dfu_dual_bank_ble_s110_pa10028...
Hi all, i'm trying to understand how to program my nrf51 DK in order to perform a temperature measurement with the onboard sensor, convert the battery voltage with the ADC...
I use dfu_dual_bank_ble_s110 bootloader from SDK10. I want the bootloader to check whether if incoming firmware is compatible with the device it is uploaded to (i.e. device...
Hi
I want to connect to only a single master device by s110. I used the example parameter setting from "ble_app_hids_keyboard" for gap_params_init, advertising_init and...
I have modified the Android Blinky App to connect two peripherals (nRF52 DK)
Scanning and Connecting to two peripherals works.. but when i want to start sending notifications...
Hi, all.
I want read mouse cursor coordinates from connected target(PC or iPhone and so on) through HID.
And then, i want to align the mouse cursor in the target center...
