We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
I used nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0, the ble_app_uart_c example code.
I want to add the timer, after add the following code, my system can't work....
Hi - I have been unsuccessful using Master Control Panel 3.10.0.14 on win10 to send a new application to a pca10028 with running initial application that supports DFU. What...
Hi,
Using the nRF52 dev kit with S132 Soft Device, with code based on examples with notifications.
I'm trying to send 20-byte notifications to an Android central each...
Hi all, I'm using MDBT40Nano from Raytac corporation with nRF51822 chipset. I tried to connect to my Segger J-Link Base but I'm not able to see the motherboard in nRFGo studio...
Hi all,
Our project base on platform nRF5_sdk11.0.0_89a8197 and use softdevice ANT_s332_nrf52_0.9.1.alpha.hex and refer to demo on path \nRF5_SDK_11.0.0_89a8197\examples...
Hi,
I'm trying to program a nRF51822 board following this tutorial ( chisight.wordpress.com/.../) using OpenOCD in a Raspberry PI.
I have been able to burn the compilated...
Error: L6218E: Undefined symbol ble_bas_battery_level_update (referred from main.o)
Error: L6218E: Undefined symbol nrf_drv_saadc_buffer_convert (referred from main.o)
Hi devs,
I am working in an nRF52 DK.
The attached example is not working when I change the SCL and SDA pins of TWI1 module. This is also not working if I disable TWI1...
Hi,
Is there any software I2c library or example projects for nRF52 devices (PCA10400) with pin configuration, read and write functions? I am using an SMBus based sensor...
Hello,
I am testing the ble_peripheral example of ble_app_uart (SDK 12, soft device 130), this has been asked at a lot of places that the MTU is limited to 20.
But then...
Hi,
I am using nRF51822 and implemented timer-2 with 2 sec capture/compare interrupt rate. But if I want to read timer's current count before it generates interrupt or...
at nRF51 SDK v9.0.0, S130, PCA10040, at peripheral side
If we receive a characteristics less than 20 bytes, we can get the correct handle value(like 0x3B). And then everything...
