At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I would like to have a confirmation of my interpretation of the consumption information that I found in the NRF51822 product spec to estimate the power consumption...
Hello,
reading the revision history in the S130V2 document, it seems only documentation has been changed.
Are there any specific functionality / bugfixes / api changes...
i want to use 2-wire to do the communication of two nrf24le1. one is the master, another is slave.
I don't know how to set up the master and slave.
Is it the code shown...
Hello All!
I am going to use nRF52832 as a network co-processor. I will be using UART as the interface between the main processor and nRF52832.
My question is how to go...
Hi,
i update my characteristic every 1 second with a new value. the notification is set for the characteristic and it will notify my phone about the new value.
at the...
I have a PCA100028 not working anymore. not sure what I have done to the board.
I have a couple of other PCA100028's work well on the same computer.
The program left on...
hi
its first in this event
on_ant_evt_channel_closed
and then
storage_access_complete_handler();
then it try to advertise by this
sd_ble_gap_adv_start...
I use s130 /center ble_hrs example , add 7 peripheral characters and add dfu,but when I want to update codes, I find it start dfu,start bootloader and connecting.... all the...
hi.
in s110 there is no problem but when use example ble_ant_app_hrm in s310 nrf51422 the ble getting error.
its error code is 536881912 :( .
in debug point error ocure...
hi.
i wrote a program in s110 and it work fine . in it i creat my own service .
but when i want use my service in s310 softdevice in this line i get error forbiden or error_code...
How can I flash SD110 and Serialization on Wavetek's WT51822 shield? I am working with an ST nucleo64 and mean to use STlink for flashing.
I found an application note from...
what is the procedure to find connected device is bonded or not, should i store the device, application or service context in persistent memory to help recognizing bonded...
Hi Nordicsemi,
I am working on peripheral BLE device, the device accessible from smartphone i am also writing the smartphone app, i want just my app to be able to connect...
Just received my Nordic nRF Smart Beacon Kit and was following the instructions in the User Guide to get setup. I inserted the battery into the beacon and there's an LED flashing...
My project is working but nRF connect does not seem to show it properly when advertising. It shows up for a moment then dissappears then shows up a while later on the RSSI...
