I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hi,
I have a nRF51822 Development Kit and a nRF51822 Bluetooth Smart Beacon Kit. I want to run on the nRF51822 Smart Beacon Kit the nRF-Sniffer (v1.0.1) application. The...
how i used central send data to peripheral.
one broad use S120and other broad use S110.Now i see explame is nrf51822\Board\nrf6310\s120\experimental\ble_app_hrs_c..have another...
In ble events handler after connecting to peripheral device i handle BLE_GAP_EVT_CONNECTED event and try to identity connected device:
case BLE_GAP_EVT_CONNECTED:
{
...
Use "nrfjprog.exe --eraseall --programs s110_nrf51822_7.0.0_softdevice.hex --program app.hex bootloader.hex --verify --reset" to flash my device, return a error "write_and_verify_hex_file...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
As I've seen many others have done, I bought the nRF518822 Development Kit not seeing that I needed the $400 nRFgo motherboard.
Searching around reveals that shouldn't...
I am trying to get the Arduino DUE up and running with the Redbear v2 BLE shield, and SDK 0.9.3.
It was a pretty trivial operation with Arduino YUN, but I not so much for...
Hi Nordic-Team,
I've spent a while trying to figure this out but I couldn't. I need your help.
I want to load the S310 softdevice to the nRF51422 chip + the blinky example...
Hi,
I am using the ANCS experimental library and am experiencing a very strange bug.
I am requesting to attributes: APP ID and Title whenever I get a notification source...
Hello,
i have some trubble with my current power consumption. I have already read other user question and solutions but nothing works for me. To reduce the power consumption...
I have built and installed bluez 5.21 on ubuntu 14.04 witout problem (see for example this recipe ).
My nrf51822 EK dongle PC10000 is not recognized by hcitool:
hcitool...
What exactly is block size in pstorage?
Desired block size for persistent memory storage, for example, if a module has a table with 10 entries, each entry is size 64...
I'm looking into using the CMSIS RTOS on the nRF51822 with the S110 softdevice which I've used successfully with other Cortex M0 MCUs. I realize the S110 isn't well tested...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
