I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hello,
I developed a BLE based application using nRF51822 softdevice S110.
This application is very low consumption.
The device connects every 60 seconds, and can send...
I try SDK hid mouse example this days, In SDK v4.2.2 it does not work sometimes when I press button 0~3 ,and some times the mouse arrow move slowly when I press the button...
Hi,
I'm trying to make the nRF module work with an older IO demo board. Does the flexible GPIO system via pin crossbar allow you to modify the pin assignments of the SWDIO...
I what to send button data , how to construct button data array :
uint8_t buffer[INPUT_REP_BUTTONS_LEN]; in function ble_hids_inp_rep_send() ?
In SDK mouse demo I can...
I want to add to lbs service battery service(bas) as well. One of the changes is in the advertising_init() function:
static void advertising_init(void)
{
uint32_t...
Hi,
We have a custom board, with accelerometer sensor, our ultimate aim is to collect the accelerometer data and transfer it to the master device (PC or smartphone) using...
Hi there,
Will any 4.1 features by making their way into the respective Soft Devices any time soon?
I would imagine 32-bit UUIDs would create some memory pressure on...
I am trying to use Eclipse+GCC for my projects. I found a similar issue as stated in the following post:
devzone.nordicsemi.com/.../nan-29-nrf51-sdk-no-project-files
...
I am having trouble getting up and running with the development kit (without the starter kit).
My setup is as follows:
The PCB antenna module is hooked up to the JTAG...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
