Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear all,
we're at the pre-production stage, I would like to ask here in the forum the suggestion and/or your experience with fabs in Europe.
What we are looking for...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi all
I’m trying to use the OTA DFU with nrf51422 SDK 6.0 and softdevice s310 V1.0.0. I were supposed to use the nrf tool application for android, but I can’t make it...
Hi
I added some random data under scanned Response as manufacture specific data .Iam using NRF_sniffer & wire shark to view the advertising packets.But in wireshark i couldnt...
Hi All,
We am trying to check and interface Nordic's EMK with custom board running android kitkat.
Problem is we cannot access internet/play store from custom board...
Hi,
I'm using nRF51 BLE driver on PC to simulate BLE peripheral using PCA10000 v2.2 dongle.
I need to add some functionality to the default connectivity app. So I compiled...
Hi, and thanks for reading this.
I attached additional LED to nRF51822 p0.24
however I can not find how to handle it .
if I want to use this function
nrf_gpio_pin_set...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
Hello,
I am using a nrf51422 development kit with softdevice S310 and I have a problem in whatever pin I choose as output when I use the bluetooth.
I run the example...
