Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm trying to understand how pstorage allocates storage.
PSTORAGE_FLASH_PAGE_SIZE is fixed, that's the actual size of a flash page and thus a basic unit as you can only...
Hi, I am trying to change the beacon data.
I changed Beacon UUID already, but I can not find where can I change device name.
I guess I need to change the gap_adv_data...
Hi,
I am upgrading to SDK 6.0.
What function should I use for retriving the whitelist data?
SDK 5.2:
//err_code = ble_bondmngr_whitelist_get(&whitelist);
//APP_ERROR_CHECK...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi,
How to implement the static PIN type pairing, when the server device doesn't have keyboard or display? Our requirement is, Master will initiate the pairing process and...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
I am trying to implement a Time-On-Air measurement with two nRF24L01+.
I set up the devices to work at 2Mbps, 3 bytes address, 1 byte payload, 1 byte CRC.
Both works...
I'm using the nrf51822 evaluation kit. There is low level access (via memory registers) the the 2.4Ghz radio in either a Nordic proprietary protocl mode, or Bluetooth LE mode...
Hello Nordic Semi,
We are using the nRF24L01+ for a remote switch application. We have a small transmitter button (nRF24L01+ layout as per datasheet with micro controller...
I have a problem within the following szenario:
I transfer data from my nRF51822 Peripheral to a connected Central (Android App) as a bunch of Notifications with maximal...
