According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I am trying to use the HCI UART application with channel sounding enabled and communicating with an external host. I was able to perform all CS procedures, and when it was...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
I'm currently developing a USB dongle using the nRF52840 , and I'm facing an issue with inconsistent data reception intervals. I’d appreciate your insights on this problem...
Hi,
Our team is interested in WiFi location service in Cloud Services.
https://www.nordicsemi.com/Products/Cloud-services/Location-Services
However, under the WiFi...
Hi,
I'd like to know how can I implement a Scene Server for one or more Generic Onoff Servers (typically leds).
I read the documentation related to Scene Server and I...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Nordic published a great blog in 2022: "Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK." It clearly explains the range capabilities of the...
I'm using Zephyr/NCS v2.7.0 with a custom multi-image project based on sysbuild . My top-level project has a sysbuild.conf at the root, and a sysbuild/ folder containing a...
Hi Nordic team,
I'm trying to stream audio from the nRF5340 DK to a BLE headset ( Sony inzone buds) using the [ Unicast Audio Client sample ] with the BAP profile.
Initially...
