I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I did some modification from radio test example.
But I don't know why the function "rand8" never ending.
In the function, rand8,
NRF_RNG->EVENTS_VALRDY = 0;
while (NRF_RNG...
Hi,
I have been trying to get up and running since the first DK was released for nRF52x and I am yet to have installed a working development environment. I have tried to...
I'd like to use a DMA channel on the nRF52 to copy RAM from one block to another. However, there doesn't appear to be any DMA controllers that are not directly associated...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
i am using nrf52832 and programmed it with eclipse by blinky example.. now i have to debug the project , but when i debug the project with the configuration given in tutorial...
Hi,
We are using a BL652 from Laird, embedding a nRF52832. We wanted to give Zephyr a try, but we are facing a problem.
We compiled the blink example, but when we flash...
Hello dear Nordic members,
I got a theoretical question: I want to connect two chips, one as central and the other as peripheral. Is it possible to stop advertising procedures...
I am using nrf51822 for a BLE project as peripheral role. I am using S110 soft device (SDK version 10).
I want to store bonding information, GATT data and all data storage...
