Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I want to undestand this. I can't see any examples with it. In the example ble_app_proximity I always received 100% level.
If it possible, can anybody give a ADC config example...
I am working with a Blend Micro Board (Arduino IDE with RBL_nRF8001 sdk), using
Evothings.
Using the RedBearLab Simple control example I can easily connect to the board...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
OpenThread recently merged a DNS client into the main branch. DNS would be extraordinarily useful because my code accesses content behind load-balancing servers with dynamics...
In this example code:
nRF5_SDK_13.0.0_04a0bfd/examples/ble_peripheral/ble_app_proximity/main.c
Where the ADC is configured to read the battery voltage:
nrf_saadc_channel_config_t...
Hi,
I've read a couple of threads in this forum that suggested that the DEVICE_MANAGER_APP_CONTEXT_SIZE value (which should be a multiple of 4) is supposed to be 16 bytes...
We're using the nrf51 with the RFAxis (now Skyworks) 2401C amplifier, which is a fixed gain 20dBm amplifier. The goal is to have a longer range 'beacon' type product and the...
What would be the best BLE Library or Framework for Raspberry-pi to exchange with nordic?
I'm trying to get data from the NRF51's GATT data.
But there are no reference...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...