Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Dear all,
i building the example light_switch_server_nrf52832_xxAA_S132_7.2.0 from solution l ight_switch_server_nrf52832_xxAA_S132_7.2.0 in configuration Debug (SDK nRF5...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hi all,
We've followed the reference EVK designs closely and are now in the Pre-Production phase.
The initial development board was intentionally large to accommodate...
Dear Nordic,
We’re working on a Smart Door Lock project built on custom hardware that includes an nRF5340 and several other controllers. For firmware updates, we’ve adopted...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi,
We want to enable zephyr shell over RTT on our custom board based on nrf52840. I tried the 'shell_module' sample with prj_minimal_rtt.conf and it works fine on nrf52840...
Hi there,
I built a battery powered custom PCBA with the NRF54L15 and the nPM1300. All the configuration and register work via I2C seems to be working properly (reading...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
I am trying to use TTM (nRF Thread Topology Monitor package) with a newly bought nRF52840 Dongle (PCA10059) on Windows.
Following the instruction at https://docs.nordicsemi...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hi,
I am trying to install NCS v3.0.1 on Ubuntu 24.04 PC and I get the following error.
Looks like ZEPHYR_BASE is not setup. I am trying to follow the Fundamentals Course...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
1st problem:
There are some failed case when i run \v2.9.1\modules\bsim_hw_models\nrf_hw_models\tests\zephyr_apps\54_aar_ccm_ecb\src\test_ccm.c
2nd problem:
If I...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
