Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
Hi there!
I found out that there is some problem in the example ble_app_hrs_rscs_relay in nRF5_SDK_11.0.0_89a8197. I want to restart advertising when adv timeout. I did as...
I'm trying to use app_timer_cnt_get() to implement an RTC Calendar system on a Gigawit module (nRF51822).
I have a test app_timer that has presacler=0 and period=3 seconds...
This is no a question, but i was not sure where to post it.
I was trying to use the nrfjprog command with the new version of SEGGER JLink, but the terminal output was ...
Hi! I'm trying to work with the beacon kit, but I have some confusion about which type of sdk I can use because with some example that I have found it doesn't work.
Besides...
When i use ble_app_hrs to connect with hrs demo(ble_app_hrs example), everything is ok.But when i connect to a heart rate monitor, it always disconnect.The print information...
I try to stop the advertising by using ble_advertising_start(BLE_ADV_MODE_IDLE) when the advertising is ongoing. It fails.
Please tell me how to stop advertising when the...
I have a problem where a central device (iPad) has to connect to a peripheral (running nrf51822, s110) as quickly as possible, receive data and disconnect again.
Right...
Hi
I would like to implement a radio peripheral in 2.402Ghz frequency which transmits some data, say of 31 bytes in radio which includes all header information abiding BLE...
I have a transmitter that sends 24 bytes of data every 10 ms. Whenever I run the receiver I only get new data once, then nothing. Here's my code
void mirf_config()
{...
hello,
I am testing the android application with nRF 52832 (s 132).
With android-Log, it is supposed that connection can not be done with the following log.
Please give...
Hi
i want to create specific service on ble so that only my mobile app should recognize it and able to connect to it.
i have gone through devzone.nordicsemi.com/.../ ...
