After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
When we define a CMake presets file in an application folder and try to load a preset from it in the "Add Build configuration" tab created by the nRF Connect Extension for...
I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Dear Team
Background: nrf5340DK board with periodic_adv_rsp sample, nrf54L15 with periodic_sync_rsp sample, SDK version is 3.0.2
Below is 5340 RTT information
Below...
Hello,
I have this problem when I try to generate the key: Key generation failed: -134
Here is the prj.conf file:
CONFIG_BUILD_WITH_TFM =y
# CONFIG_TFM_PROFILE_TYPE_MINIMAL...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
