Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
Hi all,
I have a custom board with an 9151, I want to use mqtt with aws, it's works I'm able to connect aws, but I have a question about
If I want to be able to connect...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hello Nordic Team,
I am requesting clarification on the capabilities of my nRF9151DK to be used as a debug and flash probe (via the 'debug out' P20 headers), and compare...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
I am developing a new architecture for my project. So, I am getting data from the peripheral, a custom nrf52832 card. Also, I create my custom service to send data and add...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
Hello Everyone,
I am using NRF52840 dk evaluation board Arduino ethernet shield which has W5500 ethernet chip and for my development purpose using SDK 2.6.1 on visual...
hello to all.
i been strugling the last couple of days to make a simple PPP connection from a debian12 laptop to the internet passing trough the nrf9151. I followed the...
DECT NR+ HARQ communication and testing
Hello,
we using two nrf9151 development boards with latest modem firmware version DECT-NR+ (1.0.2) and nrf-connect v2.9.0 and...
