hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
In table 32 on page 25 of the NRF51 Reference Manual, there are a bunch of registers with the description "Reserved for Nordic firmware design" or "Reserved or Nordic hardware...
Dear nordic.
I am testing with nRF51822, and have some question about hardware stability check.
nRF51822 have Clock Monitor Unit (Clock fault detector)?
Is WDT same...
I am running a standard schedule loop where I wake-up, service any scheduled tasks, then immediately go back to sleep. However, I am observing the following pattern:
...
Hi,
Everyone,
I have been working with Nordic NRF51422 with keil since laste 4 months.
Now I want to make Dev kit working on windows machine with eclipse GCC
Following...
Hi everyone,
When I run 4 instances (i.e., x2 PWM channels) of PWM with S210 (same example as the ant_background_scanning from SDK 10), after few seconds of constantly...
Hi, I am following the tutorial devzone.nordicsemi.com/.../ . to try to use eclipse to program and debug.
I have installed Eclipse on windows and I can compile without...
Timers are defined by a macro: APP_TIMER_DEF. This unfortunately expands to:
#define APP_TIMER_DEF(timer_id)
static app_timer_t timer_id##_data = { {0} };
static const...
Hi, we're working on a project that involves constant streaming of gyroscope and accelerometer data from an NRF51822 based module to a Linux machine.
What we've been working...
I am using the ble_uart_app on the dev kit with the nrf52. SDK version 11.0.0. How do I get the bsp_event_handler to get fired on a button release and button push event and...
Hi, I'm using stlink + openocd to flash and debug and it works fine.
But I want to measure the current consumption with nrf51822 debug interface off
Is there an equivalent...
I have a high-speed signal which I would like to sample with the nrf51's ADC. The signal is periodic (80kHz) and is from a low-impedance source (op amp buffer). I don't need...
I've been searched windows sample application for bluetooth.
I got android sample code but I need MFC sample code now.
If you have the sample code please let me know.
...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello,
If I supply 1.85V on the "External supply" pins, can i use all the modules of the board (nRF51DK)?
I need to have less than 2V on some of the pins as an output...
