Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi!
I'm currently developing a driver to communicate with a sensor via I2C using the Nordic's nrf_drv_twi library. I based my code on the twi_sensor example, but since...
We are in process of identifying the right hardware for our project and considering nrf52832 as the core processor. For our requirements, we need to use external serial NOR...
Hi,
I was trying to complie my code but the Keil is giving this error, which I am pretty sure is about the recent update that I have downloaded. I am using nRF51822xxAA...
hi i am using nrf51 development kit. i have gone through nordic development zone tutorial to use Eclipse IDE. build was successful it is creating release folder in which i...
We are interfacing serial flash using SPI interface and use nordic nrf52 nrf_drv_spi.c as the library.
We have taken a look at nrf_drv_spi.c, and it seems in the api nrf_drv_spi_transfer...
I am using Nordic nRF51 Development Kit with SoftDevice_130_2.0.0.I tried to run the SDK 11.0.0's example "examples\ble_peripheral\ble_app_gls\pca10028\ser_s130_spi" from...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
Hi
my idea is to open and close pipes identified by BLE address of device.
Currently I enable ESB on BLE disconnect using timeslot API.
How can I do this "on the fly...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...