Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I will try to use the s110 8.0.0
But I can not find the sdk installer from the website.
Three months ago, when I visited the website, there is a SDK 6.xx.xx Installer...
Hi.
I'm currently receiving advertisement packet from beacon scanner app. (nrf51822)
(ble_peripheral/experimental_ble_app_multiactivity_beacon/hrs_scanner)
I tried...
Hi, I am here in the use of Flash memory data when there is a strange question to consult.
Due to my side of the application, you need to enter each case sd_power_system_off...
Using nRF51 SDK 10.0, it seems like many debug prints are incorrect, triggering a GCC format warning resulting in a compilation error with -Wall turned on.
A workaround is...
I'm using a custom designed PCB around the NRF51822 that broadcasts accelerometer readouts on a characteristic.
The application is based on s110 uart example and has been...
i wantto compile ''ble_app_hrs_c'' from sdk
but it always show up likes
" C:\Program Files\CodeBlocks\MinGW\include\SDK 7.2\examples\ble_central\ble_app_hrs_c\main.c|19...
keil use pclint, it will give lots of info message or warning message.what 's the best configuration to filter these info message ?? just display the error or warning message...
Hi
I'm trying to test UART over BLE using A custom board with a nRF51822,S110_NRF51822_7.1.0
SDK 6_1_1, Code is Github "NordicSemiconductor/nRF51-ble-app-uart-static-passkey...
I'm a beginner, the question might be simple but its really important for me.
What would the current flowing through Empty nrf51822 when it is completely erased or empty...
In bootloader of sdk9
I find
ble_gap_addr_t addr;
err_code = sd_ble_gap_address_get(&addr);
APP_ERROR_CHECK(err_code);
// Increase the BLE address by one when advertising...
Dear sir,
We are using the NRF24LU1P-F32Q32-T chipset.We have unmounted chip that we are using for our application .We have made a pcb developement board on NRF24LU1P-F32Q32...
Hi,
In my project I am using rev3 nrf51822-QFAA chip set with s130 soft device.while I compiling getting the error "region RAM overflowed with stack". Then I followed some...
