I have designed a custom board and it has following components: BMD300 (Module based on nRF52832 IC) MPU9250 GPS (L80-R QUECTEL) There are some other components as well but...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
We found one charging issue on nPM1100, after we assemble the battery to the PCBA, and then apply 5V to nPM110 (VBUS) and GND. The protection ciruit does not release, and...
Hi Nordic,
I am evaluating the nrf52833 DK with nrf connect SDK. I am using by dev kit here as a central devie and I want to get the RSSI values of the periherral devices...
Hi,
I am using nRF9160 (custom board) and Zephyr V2.6
I am currently working with the nRF9160 on a custom board and utilizing Zephyr v2.6. In my application, I've observed...
Hello Team,
I have few question related to network core bootloader.
1. Does b0n verify net core image signature before booting ?
2. who uses provision partition...
We have a project based on nrf5340 audio demo,Now we upgrade SDK from NCS2.4 to NCS2.6.
But when I built the DFU, I found that FLASH was not enough
I know this problem...
I want to read data from 8 channels of ADC, when configuring all channels it shows that some of the pins are pre-occupied by other nodes. i have applied different things to...
Hello everyone,
I'm working on a Zigbee project that has the Thingy:53 as an end node. The program of the Thingy is a variation of the Zigbee Weather Station .
I'm measuring...
I am attempting to work thru the tutorial exactly per the instructions, and I'm stuck in Lesson 1 at
6. Wait for the device to connect to nRF Cloud.
The Cellular Monitor...
Hi,
I am unable to add FEM support to nRF21540, Running on ncs 2.6.0 Vscode Zephyr. I am using BLE Peripheral_hr sample. I was following this doc .
This is my error
...
Hi all, i have some problem while i try to estabilish an LTE connection . I'm using nordic n9160dk. I just search through the site, and i see a lot of topic like this , or...
Hi Nordic,
I am evaluating the nrf52833 DK with nrf connect SDK. I am using by dev kit here as a central devie and I want to get the RSSI values of the periherral devices...
Hello,
I'm currently working on using a MAX86141 sensor ( datasheet found here ), and I've been running into some issues with communicating with it since this is the first...
On a new board based on nRF9160 I am having trouble figuring out how to bring up the board.
I am using Azure IoT hub and can successfully build an application that can connect...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
We have used hundreds of thousands of Nordics over the last few years and have never actually had any larger problems with programming.
In the last production batch, 200...
I am using nrf52840 and i am working on nrf connect sdk v2.6.0 in my overlay file SPI CS pin is low but it is going high between the communication. Data is not receiving from...
Hi Nordic
When inspecting the nRF Connect SDK information, the headlines show that BLE stack has obtained BLE qualification.
Digging a bit deeper, it turns out that this...
Hi,
I am using nRF9160 (custom board) and Zephyr V2.6
I am currently working with the nRF9160 on a custom board and utilizing Zephyr v2.6. In my application, I've observed...
Hi, when I use other modules (like NRF_LOG ecc) no problem, when i use UART or UARTE the script is ok but i can't see anything on PuTTY terminal. In my case, a LED should...