Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello, I am having issue to migrate a working project based on Azure IoT Hub Application code from 1.7.0 to 2.7.0, I have resolved all errors associated with changing the...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
Hi
I've playing around with the new peer manager a while. I used the example "ble_app_hrs_rscs_relay_pca10028.uvprojx" from the SDK10. After a first fix (see Link ) in...
Hi,
I want to use timer1 or 2 interrupt ISR to generate complicated PWM signal.
but the timer->intenset setting cause ble connection drop problem.
Please refer to my...
Hello. I'm having the following connection module with nRF51822 chip.
It was purchased here .
I've found example sketch for Arduino but i can't understand how to wire...
Hi,
I have been developing using some development modules from WaveShare (based on the nRF51822 QFAC) and they work fine.
However, I'm now trying to use a module better...
Hi Nordic Expert,
I am Alex and have been developing with NRF51822 for a long time. Thanks for your quick help before. Now our product bases on S110-7.1.0 and SDK-6.1.0...
Hi
i wrote the program which is making pulse one time on channel 0 and then followed by channel 1 and then again channel 0 and then 1 going on , my aim is to create pulses...
Hi all,
I am tring to connect more than two peripherals to contral device.
I am using sdk10 and three evaluation bords nrf51822.In on device i debbuged the code of uart...
My problems with Eclipse Luna continue. Going on holiday for a week I assumed the good fairies would sort it out, but no,,,
Anyhow, I'm sure it's some path error somewhere...
I'm trying to figure out something I'm seeing. I've modified the relay demo in the nRF52 SDK so that when I press button 2 on the board, it destroys any connections, erases...
Hello Everyone,
I have configured gpio pins for buzzer pin6 and pin 7 and am trying to clear those pins after buzzer making the beep sound but it is not getting cleared...