Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I have a sensor HTS221 that I would like to power from an nRF52832 I/O to allow programmatically resetting the sensor. Looking at section 20.4.1 GPIO Electrical Specification...
We have bots (what I'm calling our device for this question) that play both the peripheral and central role depending on their context (not unlike the relay example; except...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
HI,
Currently I try to run example/iot/tcp/client in nrf51 iot sdk on nrf51-dk board. Then on server side, I use "ping6" command to test the data sending and receiving...
Hi, Very happy to note that you are planning to release source for nRF Connect for Desktop soon. Do you have an updated timeline on that?
Also, I am trying to use pc-ble...
Noticed this for gcc with -0s optimization an application fail to save a bonding data. It is caused by byte alignment of
static uint8_t buffer_memory[(n_blocks) * (block_size...
Hello everybody,
I am a newbie, and I tried to follow this tutorial to set up my laptop for development.
Everything works until I went to the step "Import existing Eclipse...
Hi,
I am currently writing the firmware of one of our products that will be produced in mass market, and now my goal is to have a unique BLE device name for every sample...
I am trying to study the docs for GPIOTE in SDK12 and see various sections for GPIOTE. What are the differences between: Driver , Abstraction , Handler and Handling Library...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
Hi All,
I am using nRF51822 for my application.
how to change the App timer Interval dynamically means i have to change the timer interval before timeout.
