I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
In my application, I take mac address of chip and make major, minor value (device 's ID) and I need mac address is a constant value. As I know, mac address is a...
because license is so expensive, I'm converting my project to OSX GNU
I'm solving problems step by step..
and there is error that I couldn't understand.
Anyone can...
Is there any way to control BLE shield 2.1 from PC rather than android / iOS app.
Also if i pass any message to BT dongle how to check the received messages.
And in...
infocenter.nordicsemi.com/index.jsp
I see a debouncing filter in the block diagram of NRF52 preview DK. Isnt debouncing implemented in software? So why need a HW debouncing...
Hi all,
I have two kinds of NRF24LE1 devices(A and B), and I want to realize that one device_A can communicate with 10 device_Bs at the same time. To explain it in detail...
I would like to use 3 PWM for controling RGBs. I use a softdevice because I want to control the pwm trough the MCP. But for now I just want to get it work to initialize these...
whether linux and bluez implemnted the simultaneous master and slave connections......?
or is it part of link layer only..?
does this feature need kernel support or not...
In the NRF51822 reference manual, the debug interface mode initiation routine is described as follow:
150 clock cycles with SWDIO=1.
I have already verified that a standard...
Hi,
I am wondering about the Cumulative crank revs for service 0x1816 & 0x1818
Cycling Cadence and Speed, Cycling Power Services
I dont understand why the crank revs...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Ok, so I've been trying to get to the bottom of a problem for a few days now where suddenly the app_timer is acting like it's on crack and running super fast, i.e. triggering...
hey,
i want to discover the PCA10001 board with PCA10000 board in master emulator. i have programmed the blanked PCA10001 chip with softdevice(s110_nrf51822_6.0.0_softdevice...
I want to generate PWM.
I set timer2 events_compare[0] to toggle pin 1:
sd_ppi_channel_assign(PWM_LED_HI_CHANNEL, &(NRF_TIMER2->EVENTS_COMPARE[0]) ,&(NRF_GPIOTE->TASKS_OU...
