Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
Hi guys, I just want to share my iBeacon code (over s110) developed on nrf51 dev board under ubuntu. It works fine but please feel free to improve it and share it!
I developed...
In some case sd_nvic_SystemReset() can not reset?
nrf51822 S110.
for example:
void main(void)
{
sd_nvic_SystemReset();
do something;
}
It can do somthing!!
So sd_nvic_SystemReset...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
