dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I have the nRF51822 development kit (with the new hardware revision QFAA or something), and I am using the Master Control Panel with the new 0.9 firmware for the dongle. ...
Hi in my case,
i pressed gpio button for one time it will do one event.
and for double press it will do another event . how can i do this one,
Regards
Balaji
Hi
In my case i have both 3 gpio interrupts and 4 rtc1 interrupts and have some timer 0 and 1 interrupts
also. how to set priority for all these interrupts in both while...
Hi Guys,
I am planning on using the nrf24l01+ to send data with a payload which is larger than 32 bytes, I was wondering whats the fastest way to transmit these packets...
Hi,
In the nrf51822 SDK examples, there is an example of radio_example which is used for send data and read data. I want to konw that if one module send data and then...
Hello - I am trying to port code over from a development kit over to the WLCSP nRF51822 on a custom PCB.
I am able to connect/bond with my device fine, however I am having...
Hi,
we're using an nRF8001.
Trying to find the relevant Bluetooth Specifications, we found the following mess (pardon my french!):
Core Specification 4.0, 2300 pages...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
nRF51822_Development_Kit_User_Guide_v1.3.pdf document has table 6 which indicates SoftDevice A and SoftDevice B. DK includes s110_nrf51822_5.2.1_softdevice.hex. Is this SD...
Hi,
I'm testing a BLED112 USB Dongle from Bluegiga ( www.bluegiga.com/.../).
I have not been able to use see the Nordic Board advertising. Currently testing ble_app_proximity...
I was wondering would it be possible to use a 50 ohm IC Antenna ( like this one ) for the nRF51822 with the matching circuit given for the nRF24 ( link here )?
It seems...
Hi,
Is there any difference(data rate) between sending large data packets through single characteristics and multiple characteristics?
I have created one characteristic...
Hi everone!
I need to get a timer setup which repeatly fires 2 IRQs. The first i.e. after a timer count cc0=500 and the 2nd count cc0=700. After 700 ticks the timer value...
